- Name
- Danalock
- Brand
- Danalock
- Is flirs
- Yes
- Documents
- Category Description File Manual_Primary_Lang
- Role type
- ROLE_TYPE_SLAVE_SLEEPING_LISTENING
- Categories
- Locks
- Product id
- 0x0001
- Device type
- Door Lock Keypad
- Oem version
- 81
- Library type
- SLAVE_ENHANCED_232
- Supports nwi
- Yes
- Z wave version
- 6.51.03
- Frequency plans
- EU: 869.85MHz, 868.40MHz
- Manufacturer id
- 0x010E
- Product type id
- 0x0008
- Long description
- Z-Wave Controlled door lock with keypad, and Bluetooth Smart. Operated by Z-Wave. Connect Danalock to your Z-Wave gateway - Danalock interfaces with your existing Z-Wave network through the Danalock smartphone app. Operate Danalock remotely by accessing your Z-Wave network from anywhere in the world with internet access.
- Hardware platform
- ZM5202
- Short description
- Z-Wave Controlled door lock with keypad, and Bluetooth Smart.
- Association groups
- Group Number Maximum Nodes Supported End Point ID Description 1
- Product identifier
- DanalockBTZE100Square
- Countries / regions
- European Union
- Certification number
- ZC10-15020007
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 9
- Supports explorer frames
- Yes
- From to description 0 0 turn and go off 1 1 turn and go on will turn automatically when manual turn is detected. 5 auto latch time how many seconds from the lock has been unlatched to it automatically should close again. if 0 then it is disabled. 0 1 0 0 0 from to description 0 60 how many seconds from the lock has been unlatched to it automatically should close again. if 0 then it is disabled. 6 sound disable or enable the beep sound from latch or unlatch operations(0 = disable, 1 = enable.) 0 1 0 0 1 from to description 1 1 enable the beep sound from latch or unlatch operations 0 0 disable the beep sound from latch or unlatch operations 3 mode 0 = stepper motor mode wave drive(power saving) 1 = stepper motor mode full drive(normal) 2 = relay mode 0 1 0 0 1 from to description 0 0 stepper motor mode wave drive(power saving) 1 1 stepper motor mode full drive(normal) 2 2 relay mode 4 turn degrees factor 10 turn degrees ( 1 = 10 degrees, 9 = 90 degrees etc.) 0 1 0 0 9 from to description 1 100 factor 10 turn degrees ( 1 = 10 degrees, 9 = 90 degrees etc.) 7 battery type set the type of battery that powers the device. this affects the returned battery state. 0 = 3,6 volt battery, 1 = 3.0 volt battery. 2 = mains power, changing from and to mains power requires the danalock to be excluded and included. 0 1 0 0 1 from to description 2 2 mains power, changing from and to mains power requires the danalock to be excluded and included. 0 0 3,6 volt battery 1 1 3.0 volt battery. 1 direction 0 = the motor goes clockwise when latched 1 = the motor goes counterclockwise when latched 0 1 0 0 0 from to description 1 1 the motor goes counterclockwise when latched 0 0 the motor goes clockwise when latched 2 speed (torque) 1 = slowest 2 = slow 3 = normal 4 = fast 5 = fastest 0 1 0 0 3 from to description 1 1 slowest 2 2 slow 3 3 normal 4 4 fast 5 5 fastest 8 battery alarm value when the battery level is equal to or under this value, the device will notify user with a beep sound after latch or unlatch. 0 1 0 0 0 from to description 0 100 when the battery level is equal to or under this value, the device will notify user with a beep sound after latch or unlatch. 11 async 0 = async off, 1 = async on. used if the lock is using an optional rotation sensor. when async is enabled the lock will auto calibrate if already unlatched and asked to unlatch again (used for special door locks where the key turn is asynced from the inside nob.) 0 1 0 0 0 from to description 0 0 async off 1 1 async on. used if the lock is using an optional rotation sensor. when async is enabled the lock will auto calibrate if already unlatched and asked to unlatch again (used for special door locks where the key turn is asynced from the inside nob.) texts
