- Name
- Dimmer 400W
- Brand
- Namron
- Features
- Feature Values Firmware Updatable
- Documents
- Category Description File Manual_Primary_Lang
- Role type
- ROLE_TYPE_SLAVE_ALWAYS_ON
- User icon
- 0x0600
- Categories
- All Lighting Devices, Dimming Lighting Devices
- Product id
- 0xD005
- S2 classes
- S2_UNAUTHENTICATED
- Device type
- Light Dimmer Switch
- Oem version
- HW: 1 FW: 1.00
- Library type
- SLAVE_ENHANCED_232
- Product line
- Dimmer 400W
- Supports nwi
- Yes
- Installer icon
- 0x0600
- Z wave version
- 6.71.01
- Frequency plans
- EU: 869.85MHz, 868.40MHz
- Manufacturer id
- 0x0438
- Product type id
- 0x0200
- Long description
- The in-wall dimmer is a Z-Wave device that is used to switch ON/OFF and adjust light intensity of the connected light and can be controlled by other Z-Wave devices. The In-wall Dimmer can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. The encryption mode that the dimmer supports is S2 Unauthenticated. When the dimmer is being included into a Z-Wave network, you can use your primary controller/gateway to enable encryption mode or disable encryption. (The primary controller/gateway shall support encryption mode configuration). The dimmer supports OTA and can update firmware wirelessly.
- Hardware platform
- ZM5101
- Short description
- The in-wall dimmer is a Z-Wave device that is used to switch ON/OFF and adjust light intensity of the connected light and can be controlled by other Z-Wave devices.
- Product identifier
- Dimmer 400W
- Countries / regions
- European Union
- Certification number
- ZC10-19096754
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 7
- Supports explorer frames
- Yes
- Supported command classes
- Identifier Name Key Version COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
- Supported notification types
- Notification Type Event / State System
- Value updatable by consumer by rf association groups
- Group Number Maximum Nodes Supported End Point ID Group Name Description 1
- From to description 0 0 disable 1 1 enable 2 saving load state before power failure saving load state before power failure 0 1 0 2 0 from to description 0 0 shutoff load 1 1 turn on load 2 2 save load state before power failure 3 enable/disable to send the basic report enable/disable to send the basic report to the lifeline when the load state changed (when value set as 1, re power on the dimmer, it will send basic report automatically） 0 1 0 1 1 from to description 0 0 disable to send basic report 1 1 enable to send basic report 4 default fade time default fade time (unit is second, this value has the same function as duration of multilevel) 0 1 0 255 1 from to description 0 0 instantly 1 127 1 second (0x01) to 127 seconds (0x7 f) in 1 second resolution. 128 254 1 minute (0x80) to 127 minutes (0x fe) in 1 minute resolution. 255 255 factory default duration. （1 second） 5 setting minimum brightness value setting minimum brightness value 0 1 0 50 0 from to description 0 50 the bigger the value is, the higher the load’s minimum brightness is 6 choose mosfet driving type choose mosfet driving type 0 1 0 1 0 from to description 0 0 trailing edge 1 1 leading edge texts
- ID Description Value 5
