- Name
- S2 Dimmer
- Brand
- Zooz
- Features
- Feature Values Electric Load Type
- Documents
- Category Description File Manual_Primary_Lang
- Role type
- ROLE_TYPE_SLAVE_ALWAYS_ON
- User icon
- 0x0604
- Categories
- All Lighting Devices, Dimming Lighting Devices
- Product id
- 0xA002
- S2 classes
- S2_UNAUTHENTICATED
- Device type
- Light Dimmer Switch
- Oem version
- HW: 1 FW: 1.00
- Library type
- SLAVE_ENHANCED_232
- Supports nwi
- Yes
- Installer icon
- 0x0600
- Z wave version
- 6.71.03
- Frequency plans
- US: 916.00MHz, 908.40MHz
- Manufacturer id
- 0x0312
- Product type id
- 0xA000
- Long description
- FEATURES: - Manual or Z-Wave on/off and brightness control - Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed (neutral wire required) - Fully adjustable ramp rate for just the right on/off speed - Double tap to full brightness feature - Remembers and restores on/off status after power failure - LED indicator signals inclusion, exclusion, reset, and setting changes - Built-in Z-Wave Plus signal repeater to extend network range - Extended compatibility with LED bulbs, no more flickering! - S2 security protocol and the latest 500 Z-Wave chip for faster and safer wireless communication - Customizable LED indicator and air-gap switch for added safety SPECIFICATIONS: - Model Number: ZEN27 - Z-Wave Signal Frequency: 908.42 MHz - Power: 120 VAC, 60 Hz - Maximum Load: 100 W LED/CFL, 300 W incandescent (100 W with both sides of heat sink tabs off) - Range: Up to 100 feet line of sight - Operating Temperature: 32-104° F (0-40° C) - Installation and Use: Indoor only
- Hardware platform
- ZM5202
- Short description
- Use this S2 dimmer for fast 3-way, 4-way, and 5-way installations with existing on/off switches.
- Product identifier
- ZEN27
- Countries / regions
- United States of America
- Certification number
- ZC10-18116309
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 2
- Supports explorer frames
- Yes
- Supported command classes
- Identifier Name Key Version COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
- Controlled command classes
- Identifier Name Key Version COMMAND_CLASS_BASIC_V2
- Value incandescent led dimmable led firmware updatable value updatable by consumer by rf neutral wire required switch load capacity watts value 300 w (incandescent with all heat sink tabs on) / 100 w led's color value white association groups
- Group Number Maximum Nodes Supported End Point ID Description 2
- From to description 0 0 led indicator is on when switch is off, led indicator is off when switch is on 1 1 led indicator is on when switch is on, led indicator is off when switch is off 2 2 led indicator is always off 3 3 led indicator is always on 4 set auto turn off timer use this parameter to set the time after which you want the switch to automatically turn off once it has been turned on. the number entered as value corresponds to the number of minutes. 0 4 0 0 60 from to description 1 65535 minutes 5 enable/disable auto turn on timer use this parameter to enable or disable the auto turn on timer function. 0 1 0 0 0 from to description 0 0 timer disabled 1 1 timer enabled 6 set auto turn on timer use this parameter to set the time after which you want the switch to automatically turn on once it has been turned off. the number entered as value corresponds to the number of minutes. 0 1 0 0 60 from to description 1 65535 minutes 1 paddle control choose if you want the upper paddle to turn the light on or turn the light off when tapped. 0 1 0 0 0 from to description 1 1 upper paddle turns the light off, lower paddle turns the light on 0 0 upper paddle turns the light on, lower paddle turns the light off 3 enable/disable auto turn off timer use this parameter to enable or disable the auto turn off timer function. 0 1 0 0 0 from to description 1 1 timer enabled 0 0 timer disabled 8 on off status after power failure set the on off status for the switch after power failure. 0 1 0 0 2 from to description 0 0 forced to off (regardless of state prior to power outage) 1 1 forced to on (regardless of state prior to power outage) 2 2 remembers and restores on/off status after power failure 9 ramp rate control adjust the ramp rate for your dimmer (fade in / fade out effect for on / off operation). values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. 0 1 0 0 1 from to description 1 99 seconds 10 minimum brightness set the minimum brightness level (in %) for your dimmer. you won’t be able to dim the light below the set value. 0 1 0 0 1 from to description 1 99 % brightness 11 maximum brightness set the maximum brightness level (in %) for your dimmer. you won’t be able to add brightness to the light beyond the set value. note: if parameter 12 is set to value 0, parameter 11 is automatically disabled. 0 1 0 0 99 from to description 1 99 % brightness texts