- Name
- DIMMER SWITCH 700
- Brand
- Zooz
- Features
- Feature Values Z-Wave Scene Type
- Documents
- Category Description File Manual_Primary_Lang
- Role type
- ROLE_TYPE_SLAVE_ALWAYS_ON
- User icon
- 0x0604
- Categories
- All Lighting Devices, Dimming Lighting Devices
- Product id
- 0xA007
- S2 classes
- S2_UNAUTHENTICATED, S2_AUTHENTICATED
- Device type
- Multilevel Switch
- Oem version
- HW: 1 FW: 1.00
- Library type
- SLAVE_ENHANCED_232
- Product line
- Line A
- Supports nwi
- Yes
- Installer icon
- 0x0600
- Z wave version
- 7.13.6
- Frequency plans
- US: 916.00MHz, 908.40MHz
- Manufacturer id
- 0x027A
- Product type id
- 0x7000
- Long description
- PRODUCT HIGHLIGHTS: - Manual or Z-Wave on/off and brightness control - NEW: 700 series Z-Wave chip for better range and faster control - Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed - Scene control: trigger actions with multi-tap (select hubs only) - Smart bulb mode: disable relay and control the light via Z-Wave - Night light mode: press down when off to turn lights on to 20% - Adjustable LED indicator in 4 colors and 3 brightness levels - Works with LED and incandescent bulbs (don’t use with tubes) SPECS: - Model Number: ZEN77 VER. 1.0 - Z-Wave Signal Frequency: 908.42 MHz - Power: 120 VAC, 60 Hz - Maximum Load: 100 W LED, 300 W incandescent; DON’T use with fans or tube lights - Range: Up to 500 feet line of sight - Operating Temperature: 32-104° F (0-40° C) - Installation and Use: Indoor only
- Hardware platform
- ZGM130
- Short description
- Meet the new Z-Wave Plus S2 Dimmer 700 Series with Simple Direct 3-Way, Night Light mode and Smart Tap scene control features.
- Product identifier
- ZEN77
- Countries / regions
- United States of America
- Supports smart start
- Yes
- Certification number
- ZC12-21030189
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 2
- Supports explorer frames
- Yes
- Supported command classes
- Identifier Name Key Version COMMAND_CLASS_CONFIGURATION_V4
- Value central scene color value white electric load type value incandescent elv (electronic) dimmable led firmware updatable value updatable by consumer by rf neutral wire required switch load capacity watts value 100 association groups
- Group Number Maximum Nodes Supported End Point ID Group Name Description 2
- From to description 0 0 led indicator is on when switch is off, led indicator is off when switch is on (default) 1 1 led indicator is on when switch is on, led indicator is off when switch is off 2 2 led indicator is always off 3 3 led indicator is always on 1 on/off paddle orientation choose if you want the upper paddle to turn the light on or turn the light off when tapped. 2 1 0 2 0 from to description 0 0 upper paddle turns the light on, lower paddle turns it off (default) 1 1 upper paddle turns the light off, lower paddle turns it on 2 2 any paddle turns light on/off 3 auto turn off timer use this parameter to enable or disable the auto turn off timer function (the time after which you want the switch to automatically turn off once it has been turned on). 2 4 0 65535 0 from to description 0 0 timer disabled 1 65535 minutes 5 auto turn on timer use this parameter to enable or disable the auto turn on timer function (the time after which you want the switch to automatically turn on once it has been turned off). 2 4 0 65535 0 from to description 0 0 timer disabled 1 65535 minutes 8 on off status after power failure set the on off status for the switch after power failure. 2 1 0 2 2 from to description 0 0 forced to off (regardless of state prior to power outage) 1 1 forced to on (regardless of state prior to power outage) 2 2 remembers and restores on/off status after power failure (default) 9 ramp rate control adjust the ramp rate for your dimmer (fade in / fade out effect for on / off operation). values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. 2 1 1 99 1 from to description 1 99 seconds 11 maximum brightness set the maximum brightness level (in %) for your dimmer. you won’t be able to add brightness to the light beyond the set value. note: if parameter 12 is set to value 0, parameter 11 is automatically disabled. 2 1 0 100 99 from to description 1 99 % brightness 10 minimum brightness set the minimum brightness level (in %) for your dimmer. you won’t be able to dim the light below the set value. 2 1 0 99 1 from to description 1 99 % brightness 23 led indicator color choose the color of the led indicator. 2 1 0 3 1 from to description 0 0 white 1 1 blue 2 2 green 3 3 red 24 led indicator brightness choose the led indicator's brightness level. 2 1 0 2 1 from to description 0 0 bright (100%) 1 1 medium (60%) 2 2 low (30%) 25 single tap behavior choose what you'd like the dimmer to do when you tap the upper paddle once. 2 1 0 3 0 from to description 0 0 the light will turn on to the last brightness level (default) 1 1 the light will turn on to the custom brightness level set in parameter 18 2 2 the light will turn on to the maximum brightness level set in parameter 11 3 3 the light will turn on to full brightness texts