Slim Multisensor

Loading…

Slim Multisensor — Philio — Off Screen Space

From to description 0 127 turn off light time 3 pir sensitivity pir sensitivity settings. 0 means disable the pir motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. high sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re trigger too frequency. 0 1 0 0 80 from to description 0 99 pir level 5 operation mode operation mode. using bit to control. bit0: reserve. bit1: 1 means test mode, 0 means normal mode. notice: this bit only effect by the dip switch setting to “customer mode”, otherwise it decides by dip switch setting to test or normal mode. bit2: reserve. bit3: setting the temperature scale. 0: fahrenheit, 1:celsius bit4: disable the illumination report after event triggered. (1:disable, 0:enable) bit5: disable the temperature report after event triggered. (1:disable, 0:enable) bit6: reserve. bit7: disable the back key release into test mode. (1:disable, 0:enable) notice: the reserve bit is allowed any value, but no effect. 0 1 0 0 0 from to description 0 0 0 255 operation mode 6 mult sensor function switch multisensor function switch. using bit to control. bit0: reserve. bit1: disable pir integrate illumination to turn on the lighting nodes in the association group 2. (1:disable, 0:enable) bit2: reserve. bit3: reserve. bit4: reserve. bit5: reserve. bit6: reserve. bit7: reserve. notice: the reserve bit is allowed any value, but no effect. 0 1 0 0 4 from to description 0 255 mult sensor function switch 7 customer function customer function switch, using bit control. bit0: reserve. bit1: enable sending motion off report. (0:disable, 1:enable) note: depends on the bit4, 0: report notification cc, type: 0x07, event: 0x fe 1: sensor binary report, type: 0x0 c, value: 0x00 bit2: enable pir super sensitivity mode. (0:disable, 1:enable) bit3: reserve. bit4: notification type, 0: using notification report. 1: using sensor binary report. bit5: disable multi cc in auto report. (1:disable, 0:enable) bit6: disable to report battery state when the device triggered. (1:disable, 0:enable) bit7: reserve. notice: the reserve bit is allowed any value, but no effect. 0 1 0 0 4 from to description 0 255 customer function 8 pir re detect interval time in the normal mode, after the pir motion detected, setting the re detect time. 8 seconds per tick, default tick is 3 (24 seconds). setting the suitable value to prevent received the trigger signal too frequently. also can save the battery energy. notice: if this value bigger than the configuration setting no. 9. there is a period after the light turned off and the pir not start detecting. 0 1 0 0 3 from to description 1 127 pir re detect interval time 2 basic set level setting the basic command value to turn on the light. the 0x ff( 1) means turn on the light. for dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. 0 1 0 0 255 from to description 0 255 basic set value 4 light threshold setting the illumination threshold to turn on the light. when the event triggered and the environment illumination lower then the threshold, the device will turn on the light. 0 means turn off illumination detected function. and never turn on the light. 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. and always turn on the light. notice: in none test mode, only the value in 1 to 99 will enable the illumination detected function and update the illumination value. 0 1 0 0 99 from to description 0 100 light threshold texts

Connectivity

Firmware

Specifications

Overview

Connectivity

Certification & compliance

Community tags

Community

Edit history

Firmware & software

Identity & commercial

Lifecycle

More specs

Similar Sensor

More from Philio