- Name
- Indoor Motion Detector
- Brand
- Nexa
- Features
- Feature Values Battery Quantity
- Documents
- Category Description File Manual_Primary_Lang
- Role type
- ROLE_TYPE_SLAVE_SLEEPING_REPORTING
- User icon
- 0x0C07
- Categories
- Sensors, Security Add-Ons, Security Systems
- Product id
- 0x0006
- S2 classes
- S2_UNAUTHENTICATED, S2_AUTHENTICATED
- Device type
- Notification Sensor
- Oem version
- HW: 1 FW: 1.00:00.05
- Library type
- SLAVE_ENHANCED_232
- Product line
- Z-Wave Plus 500 series
- Supports nwi
- Yes
- Installer icon
- 0x0C07
- Z wave version
- 6.71.01
- Frequency plans
- EU: 869.85MHz, 868.40MHz
- Manufacturer id
- 0x0060
- Product type id
- 0x0001
- Long description
- The ZMD-107 Motion Detector is a Z-WaveTM enabled device which is fully compatible with any Z- WaveTM enabled network. The device can be set up in a Z-Wave network to communicate directly with other end devices such as lighting controllers, or to report directly to a Z-Wave controller (usually a gateway). This product supports the S2 security protocol that uses encrypted Z-Wave PlusTM messages to communicate to other security-enabled Z-Wave Plus products. A security-enabled Z-Wave Plus Controller must be used in order to fully utilize the security features of this product. This product can be operated in any Z-WaveTM network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. The Motion Detector is designed with two detecting sensors, Passive Infra-Red (PIR) sensor and light sensor, in order to fulfill the purpose of security and home automation. When the detector is cooperated with security appliances, it is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the device field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Alternatively, when the detector is worked with home automation appliances, the detector can be set to perform the role of home automation device by detecting both changes in infra-red radiation levels and percentage of lux levels. Once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the device field of vision, a trigger radio signal will be transmitted so as to turn on the connected lightings for better illumination. The PIR Detector adopts a CR123 3.0V Lithium battery which under normal conditions will have typical life in excess of 1 year. When the battery level drops to an unacceptable level,,the detector will emit Battery report to the Z-Wave controller. When this occurs the batteries should be replaced as soon as possible.
- Hardware platform
- SD3502
- Short description
- The ZMD-107 Motion Detector is a Z-Wave TM enabled device which is fully compatible with any Z- WaveTM enabled network. The device can be set up in a Z-Wave network to communicate directly with other end devices such as lighting controllers, or to report directly to a Z-Wave controller (usually a gateway).
- Product identifier
- ZMD-107
- Countries / regions
- European Union
- Certification number
- ZC10-22067098
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 1
- Supports explorer frames
- Yes
- Supported command classes
- Identifier Name Key Version COMMAND_CLASS_POWERLEVEL
- Controlled command classes
- Identifier Name Key Version COMMAND_CLASS_BASIC
- Supported notification types
- Notification Type Event / State Home Security
- Value 1 battery type value cr123 3.0 v 1700m ah lithium battery firmware updatable value updatable by consumer by rf association groups
- Group Number Maximum Nodes Supported End Point ID Group Name Description 1
- From to description 1 99 when basic set command is sent where contains a value, the receiver will take it for consideration; for instance, if a lamp module is received the basic set command of which value is decisive as to how bright of dim level of lamp module shall be. 4 parameter 4 re trigger interval setting (pir sensor only) 1 2 5 3600 180 from to description 5 3600 the configuration parameter that can be used to adjust the interval of being re triggered after the detector has been triggered as configuration parameter #4. no response will be made during this interval if a movement is presented. the time interval can be set between 5 secs to 3600 secs. 3 parameter 3 sensitivity level (pir sensor only) 1 1 1 10 6 from to description 1 10 in order to provide a best efficiency of the detector, it is recommended to test the detector with movements from a farthest end of the coverage area at first time of use. if movements cannot be detected sensitively, simply adjust the sensitivity level with configuration parameter #3. this parameter can be configured with the value of 1 through 10, where 1 means low sensitivity and 10 means highest sensitivity texts
- ID Description Value 8