Skip to main content

Loading…

Smart Switch Gen5 — Aeotec — Off Screen Space

Off Screen Space

Smart Switch Gen5

Aeotec · Plug Switch

Smart Switch Gen5

View all Aeotec products

Connectivity: Z-WaveCategory: Plug Switch

Z-WaveCertified

App supportiOSRecently updated· Apr 2026

Aeon Labs Smart Switch Gen5 is a Z-Wave device that can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway), it can be controlled by other Z-Wave devices to turn on/off loads, it can bear up to 16A current of resistive loads. It also acts as a repeater that forwards Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node. By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices. Also a tool that can be programmed, scheduled, controlled and communicated with from anywhere in the world.

Want to buy adds it to your wish list and follows Aeotec for updates. I own it adds it to your collection.

Compare

vs Competitor ▾

Connectivity

Z-Wave

Firmware

Current version HW: 64 FW: 1.08

Specifications

Overview

Company: Aeotec
Category: Plug Switch
Device type: On/Off Power Switch

Connectivity

Standard / protocol: Z-Wave
Connectivity: Z-Wave
Transport: Z-Wave
Spec version: 6.51.06
Z-Wave frequency: IL: 916.00MHz

Certification & compliance

Certificate ID

Community tags

Be the first to tag this page — tags appear right away. Try a theme, capability, or subject (e.g. WWII, heist, slow burn, time travel, A24).

From to description 0 0 overload protection disabled 1 1 overload protection is enabled 80 enable/disable to send notifications to associated devices to associated devices. this parameter is used to enable/disable to send notifications to associated devices (in group 1) when the state of smart switch gen5’s load is changed. (0=send nothing, 1=send hail cc, 2=send basic report cc). 0 1 0 0 0 from to description 0 0 send nothing (disabled) 1 1 send hail command 2 2 send basic report command 90 enable/disable the function of parameter 91 and 92. this parameter is used to enable/disable the function of parameter 91 and 92 (1=enabled, 0=disabled). 0 1 0 0 1 from to description 0 0 configuration parameters 91 and 92 are disabled 1 1 configuration parameters 91 and 92 are enabled 91 induce an automatic report this parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in wattage. 0 2 0 0 25 from to description 0 32767 the threshold can be set from 0 to 32767 watt. 92 induce an automatic report this parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in percentage. 0 1 0 0 5 from to description 0 100 the threshold can be set from 0 to 100 percent. 111 set the interval time of sending report. this parameter is used to set the interval time of sending report in report group 1. (the unit of time is second). 0 4 0 0 300 from to description 0 268435456 interval seconds 2 make smart switch blink this parameter is used for customer to control the product’s load (e. g incandescent light) to blink with a certain time when you set this parameter and send this command to the load. 0 2 0 0 3850 from to description 256 32767 specifies the cycle of on/off, the unit of it is 0.1 second. 0 255 specify the time that smart switch should blink, in seconds. 101 to set which report need to be sent. this parameter is used to configure which reports need to be sent in report group 1. the values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. for example, instantaneous current is the value 2 and instantaneous watts is the value 4, so setting parameter 101 to a value of 6 will result in both instantaneous current and instantaneous watts to be reported. see the full description of the parameter values for other possible settings. 0 4 0 0 4 from to description 8 8 report accumulated k wh 2 2 report instantaneous current (amperes) 4 4 report instantaneous watts 1 1 report instantaneous voltage 102 to set which report need to be sent. this parameter is used to configure which reports need to be sent in report group 2. the values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. for example, instantaneous current is the value 2 and instantaneous watts is the value 4, so setting parameter 102 to a value of 6 will result in both instantaneous current and instantaneous watts to be reported. see the full description of the parameter values for other possible settings. 0 4 0 0 8 from to description 1 1 report instantaneous voltage 4 4 report instantaneous watts 8 8 report accumulated k wh 2 2 report instantaneous current (amperes) 103 to set which report need to be sent. this parameter is used to configure which reports need to be sent in report group 3. the values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. for example, instantaneous current is the value 2 and instantaneous watts is the value 4, so setting parameter 103 to a value of 6 will result in both instantaneous current and instantaneous watts to be reported. see the full description of the parameter values for other possible settings. 0 4 0 0 0 from to description 1 1 report instantaneous voltage 2 2 report instantaneous current (amperes) 4 4 report instantaneous watts 8 8 report accumulated k wh 112 set the interval time of sending report. this parameter is used to set the interval time of sending report in report group 2. (the unit of time is second). 0 4 0 0 600 from to description 0 268435456 interval seconds 113 set the interval time of sending report. this parameter is used to set the interval time of sending report in report group 3. (the unit of time is second). 0 4 0 0 600 from to description 0 268435456 interval seconds 200 partner id this parameter is used to configure the partner id. (0== aeon labs standard product, 1~255== others). 0 1 0 0 0 from to description 0 0 aeon labs standard product 1 255 partner id of partner product 252 enable/disable lock configuration this parameter is used to enable/disable lock all configuration parameters. (0 =disable, 1 = enable) 0 1 0 0 0 from to description 0 0 all configuration parameters are configurable. 1 1 all configuration parameters are not configurable (locked). 254 device tag this parameter is used to save the device tag, which will be written/ assigned in factory/ manufacturer. 0 2 0 0 0 from to description 0 32767 device tag 255 reset to default factory setting this parameter is used to reset product to default factory setting. (there are just 2 values can be used). 0 4 0 0 0 from to description 1431655765 1431655765 reset the product to default factory setting and be excluded from the z wave network. 1 1 resets all configuration parameters to default setting. texts