Water Sensor — Oomi — Off Screen Space

Skip to main content

Loading…

Water Sensor — Oomi — Off Screen Space

From to description 1 1 enable. 0 0 disable 10 set the alarm time for the buzzer when the sensor is triggered. set the alarm time for the buzzer when the sensor is triggered. 0 4 0 0 101968650 from to description 1 255 repeated cycle of buzzer alarm. 256 65535 the time of buzzer keeping on state (msb) 65536 2147483647 the time of buzzer keeping off state 49 set the upper limit value (overheat). set the upper limit value (overheat). 0 4 0 0 68157696 from to description 0 0 celsius unit 1 1 fahrenheit unit 65536 2147483647 temperature value 50 set the lower limit value (under heat) set the lower limit value (under heat) 0 4 0 0 20971776 from to description 0 0 celsius unit 1 1 fahrenheit unit 65536 2147483647 temperature value 9 report the current power mode and the product state for battery power mode report the current power mode and the product state for battery power mode. note: this parameter cannot be used as set usage. 0 2 0 0 0 from to description 0 0 usb power mode 256 256 keep sleep state for battery power mode 257 257 keep awake for 10 minutes for battery power mode. 64 set the default unit of the automatic temperature report in parameter 101 103. set the default unit of the automatic temperature report in parameter 101 103. 0 1 0 0 1 from to description 0 0 the unit is celsius. 1 1 the unit is fahrenheit. 84 get the state of tilt sensor get the state of tilt sensor. note: this is a get only parameter. 0 1 0 0 0 from to description 0 0 the water sensor main unit is in horizontal direction. 1 1 the water sensor main unit is in vertical direction. 88 to set which value of the basic set will be sent to the associated nodes in association group 3 when the sensor probe 1 is triggered. to set which value of the basic set will be sent to the associated nodes in association group 3 when the sensor probe 1 is triggered. 0 1 0 0 0 from to description 0 0 send nothing 1 1 presence of water, send basic set 0x ff, absence of water, send basic set 0x00. 2 2 presence of water, send basic set 0x00, absence of water, send basic set 0x ff. 89 to set which value of the basic set will be sent to the associated nodes in association group 4 when the sensor probe 2 is triggered. to set which value of the basic set will be sent to the associated nodes in association group 4 when the sensor probe 2 is triggered. 0 1 0 0 0 from to description 0 0 send nothing. 1 1 presence of water, send basic set 0x ff, absence of water, send basic set = 0x00. 2 2 presence of water, send basic set 0x00, absence of water, send basic set 0x ff. 94 to set which power source level is reported via the battery cc. to set which power source level is reported via the battery cc. 0 1 0 0 0 from to description 0 0 report the usb power level. 1 1 report the cr123 a battery level. 101 to set what unsolicited report would be sent to the lifeline group. to set what unsolicited report would be sent to the lifeline group. 0 1 0 0 3 from to description 0 0 send nothing 1 1 battery report is enabled. 2 2 multilevel sensor report for temperature is enabled. 3 3 battery report and multilevel sensor report for temperature are enabled. 111 to set the interval time of sending reports in report group 1 to set the interval time of sending reports in report group 1. note: 1. the unit of interval time is second if usb power. 2. if battery power, the minimum interval time is equal to wake up interval set by the wake up cc. 0 4 0 0 3600 from to description 5 2678400 available rang is 5 to 2678400 seconds. 135 to set which sensor report can be sent when the water leak event is triggered and if the receiving device is a non multichannel device. to set which sensor report can be sent when the water leak event is triggered and if the receiving device is a non multichannel device. 0 1 0 0 1 from to description 0 0 send nothing 1 1 send notification report to association group 1. 2 2 send configuration 0x88 report to association group 2. 3 3 send notification report to association group 1 and send configuration 0x88 report to association group 2. 136 when the parameter 0x87 is set to 2 or 3, it can get the sensor probes’ status through this configuration value. when the parameter 0x87 is set to 2 or 3, it can get the sensor probes’ status through this configuration value. note: this parameter is a get only parameter. 0 1 0 0 0 from to description 0 0 absence of water is triggered by probe 1. 1 1 presence of water is triggered by probe 1. 2 2 presence of water is triggered by probe 2. 201 temperature sensor calibration temperature sensor calibration. note: 1. high byte is the calibration value. low byte is the unit (0x00=celsius, 0x01=fahrenheit) 2. the calibration value (high byte) contains one decimal point. e.g. if the value is set to 20 (0x1400), the calibration value is 2.0 ℃ (eu/au version) or if the value is set to 20 (0x1401), the calibration value is 2.0 ℉(us version) 3. the calibration value (high byte) = standard value measure value. e.g. if measure value =25.3℃ and the standard value = 23.2℃, so the calibration value= 23.2℃ 25.3℃= 2.1℃ (0x eb). if the measure value =30.1℃ and the standard value = 33.2℃, so the calibration value= 33.2℃ 30.1℃=3.1℃ (0x1 f). 0 2 0 0 1 from to description 128 127 available rang is 12.8℃ to 12.7℃. 252 enable/disable all configuration parameters to be locked enable/disable all configuration parameters to be locked. 0 1 0 0 0 from to description 0 0 disable 1 1 enable. 255 reset to factory defaults. reset to factory defaults. 0 4 0 0 0 from to description 1 1 reset all configuration parameters to factory defaults. 1431655765 1431655765 reset the product to factory defaults. 57 set the recover limit value of temperature sensor. note: 1. when the current measurement <= (upper limit – recover limit), the upper limit report is enabled and then it would send out a sensor report when the next measurement is more than the upper limit. after that the upper limit report would be disabled again until the measurement = (lower limit + recover limit), the lower limit report is enabled and then it would send out a sensor report when the next measurement is less than the lower limit. after that the lower limit report would be disabled again until the measurement >= (lower limit + recover limit). 3. high byte is the recover limit value. low byte is the unit (0x01=celsius, 0x02=fahrenheit). 0 2 0 0 5121 from to description 10 255 available range is 1.0℉ to 25.5℉ 86 enable/ disable the buzzer. enable/ disable the buzzer. 0 1 0 0 1 from to description 0 0 disable 1 1 enable texts