Skip to main content

Loading…

Датчик движения (Motion Sensor) — Philio Technology — Off Screen Space

Off Screen Space

Датчик движения (Motion Sensor)

Philio Technology · Sensor

Датчик движения (Motion Sensor)

View all Philio Technology products

Connectivity: Z-WaveCategory: Sensor

Z-WaveCertified

The slim multisensorPST02-5B has PIR, temperature and illumination, 3 sensors function in one,based on Z-Wave technology It is the Z-WaveTM plus product, it support the security, OTA... Those newest features of the Z-WaveTM technology. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances.

Want to buy adds it to your wish list and follows Philio Technology for updates. I own it adds it to your collection.

Compare

vs Competitor ▾

Connectivity

Z-Wave

Firmware

Current version HW: 1 FW: 1.29:01.20

Specifications

Overview

Company: Philio Technology
Category: Sensor
Device type: Notification Sensor

Connectivity

Standard / protocol: Z-Wave
Connectivity: Z-Wave
Transport: Z-Wave
Spec version: 6.51.02
Z-Wave frequency: RU: 869.00MHz

Certification & compliance

Certificate ID

Community tags

Be the first to tag this page — tags appear right away. Try a theme, capability, or subject (e.g. WWII, heist, slow burn, time travel, A24).

From to description 0 100 0 means turn off illumination detected function. and never turn on the light. 1 means darkest. 99 means brightest. 100 means turn off illumination 6 mult sensor function switch multisensor function switch. using bit to control. caution: the value is unsigned byte, the range is from 0x00 ~ 0x ff. bit1: disable pir integrate illumination to turn on the lighting nodes in the association group 2. (1:disable, 0:enable) 0 1 0 0 4 from to description 2 2 disable pir integrate illumination to turn on the lighting nodes in the association group 2. (1:disable, 0:enable) 7 customer function customer function switch, using bit control. caution: the value is unsigned byte, the range is from 0x00 ~ 0x ff. bit1: enable sending motion off report. (0:disable, 1:enable) note: depends on the bit4, 0: report notification cc, type: 0x07, event: 0x fe 1: sensor binary report, type: 0x0 c, value: 0x00 bit2: enable pir super sensitivity mode. (0:disable, 1:enable) bit4: notification type, 0: using notification report. 1: using sensor binary report bit5: disable multi cc in auto report. (1:disable, 0:enable) bit6: disable to report battery state when the device triggered. (1:disable, 0:enable) 0 1 0 0 4 from to description 1 1 bit1: enable sending motion off report. (0:disable, 1:enable) 2 2 bit2: enable pir super sensitivity mode. (0:disable, 1:enable) 4 4 bit4: notification type, 0: using notification report. 1: using sensor binary report. 5 5 bit5: disable multi cc in auto report.(1:disable, 0:enable) 6 6 bit6: disable to report battery state when the device triggered. (1:disable, 0:enable) 8 pir re detect interval time in the normal mode, after the pir motion detected, setting the re detect time. 8 seconds per tick, default tick is 3 (24 seconds). setting the suitable value to prevent received the trigger signal too frequently. also can save the battery energy. notice: if this value bigger than the configuration setting no. 9. there is a period after the light turned off and the pir not start detecting. 0 1 0 0 3 from to description 1 127 in the normal mode, after the pir motion detected, setting the re detect time. 8 seconds per tick, default tick is 3 (24 seconds). 9 turn off light time after turn on the lighting, setting the delay time to turn off the lighting when the pir motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command. 0 1 0 0 4 from to description 0 127 after turn on the lighting, setting the delay time to turn off the lighting when the pir motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command 2 basic set level setting the basic command value to turn on the light. the 0x ff( 1) means turn on the light. for dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. caution: the value is unsigned byte, the range is from 0x00 ~ 0x ff. 0 1 0 0 127 from to description 128 127 setting the basic command value to turn on the light. the 0x ff( 1) means turn on the light. for dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. caution: the value is unsigned byte, the range is from 0x00 ~ 0x ff. 3 pir sensitivity pir sensitivity settings. 0 means disable the pir motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. high sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re trigger too frequency. 0 1 0 0 80 from to description 0 99 pir sensitivity settings. 0 means disable the pir motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. high sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re trigger too frequency. 5 operation mode operation mode. using bit to control. caution: the value is unsigned byte, the range is from 0x00 ~ 0x ff. bit1: 1 means test mode, 0 means normal mode bit3: setting the temperature scale. 0: fahrenheit, 1:celsius bit4: disable the illumination report after event triggered. (1:disable, 0:enable) bit5: disable the temperature report after event triggered. (1:disable, 0:enable) bit7: disable the back key release into test mode. (1:disable, 0:enable) 0 1 0 0 0 from to description 1 1 1 means test mode, 0 means normal mode. 3 3 bit3: setting the temperature scale. 0: fahrenheit, 1:celsius 4 4 bit4: disable the illumination report after event triggered. (1:disable, 0:enable) 5 5 bit5: disable the temperature report after event triggered. (1:disable, 0:enable) 7 7 bit7: disable the back key release into test mode. (1:disable, 0:enable) texts