- Name
- Z-Wave 3 in 1 Multi Sensor
- Brand
- Philio Technology
- Features
- Feature Values Firmware Updatable
- Documents
- Category Description File Manual_English
- Role type
- ROLE_TYPE_SLAVE_SLEEPING_REPORTING
- User icon
- 0x0C07
- Categories
- Sensors
- Product id
- 0x0070
- S2 classes
- S2_UNAUTHENTICATED
- Device type
- Notification Sensor
- Oem version
- HW: 1 FW: 1.02:01.02
- Library type
- SLAVE_ENHANCED_232
- Product line
- Philio Z-Wave Products
- Supports nwi
- Yes
- Installer icon
- 0x0C07
- Z wave version
- 6.81.03
- Frequency plans
- EU: 869.85MHz, 868.40MHz
- Manufacturer id
- 0x013C
- Product type id
- 0x0002
- Long description
- The multi sensor is a Z-WaveTM enabled device which is fully compatible with any Z-WaveTM enabled network. This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. Z-WaveTM enabled devices displaying the Z-WaveTM logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-WaveTM enabled networks. The product supports Over The Air(OTA) feature for the products firmware upgrade. This product can be included and operated in any Z-Wave TM network with other Z-Wave TM certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. The device adopt the Z-Wave TM 500 series chip, when your Z-Wave TM network system is all made by Z-Wave TM 500 series devices. The network system will have the advantages as below.
- Hardware platform
- SD3502
- Short description
- The multi sensor is a Z-WaveTM enabled device which is fully compatible with any Z-WaveTM enabled network.
- Product identifier
- PST07
- Countries / regions
- European Union
- Supports smart start
- Yes
- Certification number
- ZC10-19106767
- Radio range z wave (m)
- 40
- Configuration parameters
- Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 1
- Supports explorer frames
- Yes
- Supported command classes
- Identifier Name Key Version COMMAND_CLASS_POWERLEVEL
- Controlled command classes
- Identifier Name Key Version COMMAND_CLASS_BASIC
- Supported multilevel sensors
- Multilevel Sensor Type Air temperature
- Supported notification types
- Notification Type Event / State Home Security
- Value not updatable association groups
- Group Number Maximum Nodes Supported End Point ID Group Name Description 1
- From to 0 99 4 operation mode operation mode. using bit to control. 1 1 0 127 1 from to 0 127 3 pir sensitivity pir sensitivity settings. 0 means disable the pir motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. high sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re trigger too frequency. 1 1 0 99 80 from to 0 99 5 customer function customer function switch, using bit control. 1 1 0 127 3 from to 0 127 6 pir re detect interval time in the normal mode, after the pir motion detected, setting the re detect time. 10 seconds per tick, default tick is 6 (60 seconds). setting the suitable value to prevent received the trigger signal too frequently. also can save the battery energy. notice: if this value bigger than the configuration setting no. 7 there is a period after the light turned off and the pir not start detecting. 1 1 1 60 6 from to 1 60 7 turn off light time after turn on the lighting, setting the delay time to turn off the lighting when the pir motion is not detected. 10 seconds per tick, default tick is 7 (70 seconds). 0 means never send turn off light command. 1 1 1 60 7 from to 1 60 9 auto report light sensor time the interval time for auto report the illumination. the default value is 12. the tick time can setting by the configuration no.11. 1 1 1 127 0 from to 1 127 texts
- ID Description Value 1